Focused arrival windows
Useful updates and clear arrival timing.
Exposed-fastener panels installed to 140 mph wind ratings
Corrugated Metal Roofing in Freeport Built for Coastal Weather
Corrugated Metal Roofing in Freeport gives you a roof that shrugs off nor'easters, salt air, and summer hail without the constant patching asphalt shingles demand. We install 26- and 29-gauge panels over proper underlayment and ice and water shield, fasten them on a chalk line, and seal every penetration. If your roof is 20-plus years old or you are tired of chasing leaks after every storm, call us for a same-day estimate.
Prepared local crewClear options firstFinal testing and walkthrough
Clear scope before work
Review the approach and price before deciding.
Prepared, clean crews
Equipped vehicles and respectful cleanup.
Local accountability
Neighbors serving neighbors with follow-through.
What is included
What Our Corrugated Metal Roofing Service Includes
Every corrugated metal roof installation includes tear-off, deck inspection, underlayment, ice and water shield, panels, trim, fasteners, and full cleanup. We spell out exactly what is covered in your written estimate so there are no surprises. Optional add-ons like skylight replacement or gutter guards are priced separately.
Full Tear-Off and Disposal
We strip the old shingles or panels down to the deck and haul everything away in a dumpster. On a typical 1,500-square-foot Freeport roof, tear-off takes one to two days. We magnet-sweep the yard and driveway daily so nails never reach your tires.
Deck Inspection and Repair
Every board gets checked for rot, cracks, and soft spots. Damaged decking is replaced with new plywood before underlayment goes down. Skipping this step is why some metal roofs leak within five years. We price deck repairs upfront if we find them during the estimate.
Underlayment and Ice Shield
Synthetic underlayment covers the full deck, and ice and water shield runs along eaves, valleys, and penetrations. This is the waterproofing layer that protects your home if a fastener ever backs out. It is standard on every metal roof we install, not an upgrade.
Panels, Trim, and Fasteners
We install 26- or 29-gauge corrugated panels in your chosen color, fastened on a chalk line with hex-head screws and neoprene washers. Ridge caps, gable trim, and pipe boots get sealed with roofing sealant. Panel layout and screw pattern follow manufacturer specs to keep your warranty valid.
Final Walkthrough and Warranty
We roll every seam, hose-test every penetration, and walk the property with you before we leave. You get photos of the finished roof, manufacturer warranty paperwork, and a written workmanship warranty. Final walkthrough takes 30 to 45 minutes.
PLAN
Request a service estimate
Share what is happening and receive a clear next step from the local team.
Service overview
What Corrugated Metal Roofing in Freeport Actually Involves
Corrugated Metal Roofing in Freeport is a panel roofing system that uses wavy, galvanized or galvalume steel sheets fastened to your roof deck to shed water fast and hold up to coastal weather. Panels run 26-gauge or 29-gauge, come in 12- to 36-inch widths, and overlap by at least one corrugation at every seam. We lay down synthetic underlayment and ice and water shield first, then set panels with a roofing nail gun or hex-head screws fitted with neoprene washers. Ridge caps, gable trim, and pipe boots get sealed with roofing sealant rated for metal.
Homeowners across Nassau County call us because corrugated metal roofing Freeport solves problems asphalt cannot. Salt air off the bay eats through shingle granules in 12 to 15 years here, while a painted metal panel holds its finish for 30 to 40. After a storm pushes through, we see missing shingles, flashing failure, and clogged gutters causing roof damage on nearly every block. A metal roof ends that cycle. If you have been searching corrugated metal roofing near me Freeport, we cover Freeport and the South Shore villages with the same crew and same standards.
- 40 to 70 Year Lifespan — A painted corrugated metal roof installed over a sound deck lasts 40 to 70 years. Asphalt shingles in Freeport's salt air often fail at 12 to 15. That means one metal roof can outlast three or four shingle roofs, and you stop paying for tear-off and disposal every decade and a half.
- Wind Ratings to 140 mph — When we fasten panels on a chalk line with the correct screw pattern, the assembly meets wind uplift ratings up to 140 mph. That matters on the South Shore, where nor'easters push sustained gusts off the water. Losing shingles in a 60 mph storm becomes a problem you no longer have.
- Cuts Cooling Costs — A light-colored metal panel reflects solar heat instead of absorbing it. Homeowners typically see summer cooling costs drop 10 to 25 percent after a metal roof goes on. On a 1,800-square-foot Freeport cape, that can mean $30 to $60 a month back in your pocket from June through September.
- Sheds Rain and Snow Fast — The corrugated profile channels water off the roof quickly, which reduces ponding and the ice dams that form along eaves after a freeze-thaw cycle. Fewer standing-water pockets means less rotting decking, fewer roof leaks, and a roof that dries out within minutes of a storm passing.
- Same-Day Estimates — Call before noon and we will be on your roof the same day in most of Freeport and Nassau County. You get a written price with panel gauge, color, and trim spelled out. No pressure, no vanishing salesman, no surprise line items after the tear-off starts.
- 21 Years Local — We have been roofing Freeport since 2005, so we know how salt air off the bay shortens shingle life and how nor'easters test fasteners on the South Shore. That local knowledge goes into every panel layout, screw pattern, and flashing detail we install.
- Manufacturer-Certified Crews — Our installers hold GAF Master Elite and Owens Corning Preferred Contractor credentials, plus CertainTeed SELECT ShingleMaster for shingle work. Those certifications require ongoing training and insurance, and they keep your manufacturer warranty intact. We also carry full NYS roofing license, liability, and workers' comp coverage.
- Warrantied Workmanship — Every corrugated metal roof installation Freeport NY gets a written workmanship warranty on top of the manufacturer panel warranty. If a fastener backs out or a seam leaks within the coverage window, we come back and fix it. That is the difference between a handshake and a contract.
The service timeline
How Our Metal Roof Installation Process Works
Inspection and Estimate
We walk the roof, check the deck from the attic side, and measure square footage. You get a written estimate the same day with panel gauge, color, and trim listed. Most Freeport homes take 45 to 60 minutes to inspect. If we find rotting decking or failed flashing, we price that in before you sign anything.
Material Delivery and Setup
Panels, underlayment, ice and water shield, and trim arrive on a flatbed and get staged on your driveway or lawn, never on the roof. We tarp landscaping, set ladder stabilizers, and run a dumpster for the old roofing. Delivery and setup usually take half a day on a standard 1,500-square-foot roof.
Tear-Off and Deck Repair
We strip the old shingles or panels down to the deck, then inspect every board. Soft or cracked decking gets replaced with new plywood. On a typical Freeport ranch, tear-off runs one to two days. We magnet-sweep the yard and driveway at the end of each day so nails never reach your tires.
Underlayment and Panel Install
Synthetic underlayment goes down first, then ice and water shield along eaves and valleys. Panels get laid on a chalk line, overlapped one corrugation, and fastened with hex-head screws and neoprene washers using a roofing nail gun and air compressor. Ridge caps, gable trim, and pipe boots get sealed with roofing sealant. Install runs two to four days.
Final Walkthrough and Cleanup
We roll every seam with a seam roller, test every penetration with a hose, and walk the property with you. You get photos of the finished roof, warranty paperwork, and a maintenance sheet. Final walkthrough takes 30 to 45 minutes. We do not leave until you have signed off on the work.
Tools and methods01 02 03 04 05 06 07 08 09
Tools and Methods We Use on Metal Roofs
Roofing Nail Gun and Air Compressor
Used to fasten underlayment and decking quickly and consistently. Consistent depth and spacing matter for the waterproofing layer under the panels. We run a compressor on every job so the underlayment goes down tight.
Chalk Line
Snapped across the roof to keep panel rows straight and fastener spacing even. A crooked panel row shows from the street and can compromise the overlap. We chalk every course before a panel goes down.
Seam Roller
Rolls panel seams and trim edges to seat them tight against the underlayment. A properly rolled seam keeps water from wicking under the overlap. We roll every seam before the job is called complete.
Roofing Safety Harness and Ladder Stabilizer
Keeps our crew safe on steep pitches and keeps ladders from shifting on uneven ground. Safety gear is not optional on a metal roof job. Every installer is tied off when working near an edge.
Pry Bar and Utility Knife
Used during tear-off to lift old shingles and cut underlayment to size. Clean tear-off protects the deck from damage and makes the new installation go faster. We replace any decking the pry bar reveals as soft or cracked.
Manufacturer-Spec Fastening
We follow the panel manufacturer's screw pattern and spacing exactly, using hex-head screws with neoprene washers. That keeps the wind uplift rating valid and protects your warranty. Improvised fastening is the number one reason metal roofs fail early.
Ice and Water Shield at Eaves and Valleys
We run a self-adhering ice and water shield membrane along every eave, valley, and penetration. This is the layer that stops water from backing up under the panels during a freeze-thaw cycle. It is standard on every metal roof we install.
Hose Testing Before Sign-Off
Before we call a job complete, we hose-test every penetration, seam, and flashing detail. If water gets through, we fix it on the spot. You should never have to discover a leak during the first storm after installation.
Magnet Sweep and Daily Cleanup
We magnet-sweep the yard and driveway at the end of every workday. Roofing nails in the grass are a hazard for tires, pets, and bare feet. Daily cleanup is part of the job, not an afterthought.
Where this service helps
When Corrugated Metal Roofing Makes Sense in Freeport
Your asphalt shingle roof is 15-plus years old and starting to lose granules or curl at the edges.
We tear off the failing shingles, inspect and repair the deck, and install corrugated metal panels with new underlayment and ice and water shield. The job takes three to five days on a typical Freeport home. You get a roof that lasts 40 to 70 years instead of replacing shingles again in 12 to 15. No more annual repair calls, no more granule loss, no more patching.
You have a cottage or bungalow near the Nautical Mile with a low-slope roof that ponds water after every storm.
We install corrugated metal panels on a pitch as low as 3:12 with proper underlayment and sealed seams. The corrugated profile channels water off the roof fast, which eliminates ponding. Standing water is gone, so the roof dries within minutes of a storm. That stops the rot and leak cycle that low-slope shingle roofs get stuck in.
You are building a detached garage, shed, or addition and want a roof that matches the coastal look.
We install corrugated metal panels sized to the structure with matching trim and fasteners. Most garages and sheds are done in one to two days. We can match the color to your house or go with a classic galvanized finish. A durable, low-maintenance roof that looks right on a South Shore property. No shingles to blow off, no annual maintenance, and a service life measured in decades.
You are tired of paying for roof repairs every time a nor'easter rolls through.
We install corrugated metal panels fastened to a 140 mph wind uplift rating, with ridge caps and trim secured to manufacturer specs. The assembly is built to stay put when the wind blows. You stop calling a roofer after every storm. The panels stay fastened, the trim stays tight, and the roof keeps doing its job year after year.
Local execution
How Corrugated Metal Roofing Works in Freeport
Freeport sits on the South Shore, which means salt air off the bay, nor'easters in fall and winter, and freeze-thaw cycles that hammer roofs from December through March. Asphalt shingles here often fail at 12 to 15 years, while a properly installed metal roof holds 40 to 70. We install corrugated metal roofing Freeport with 26- or 29-gauge panels, ice and water shield at every eave, and fasteners set to a 140 mph wind uplift rating. The village has a mix of 1920s bungalows, mid-century ranches, and newer colonials, and each one needs a different panel layout and trim detail. If you have been comparing corrugated metal roofing cost Freeport NY, call us and we will walk your roof, measure it, and give you a written price the same day.
Nautical Mile
Homes closest to the water see the heaviest salt-air exposure. Metal panels hold their finish far longer than shingles here, which is why we recommend 26-gauge galvalume for these roofs.
Meadowbrook
Many homes here have complex rooflines with dormers and valleys. Panel layout and flashing details matter more on these roofs, and we chalk every course to keep the lines straight.
Freeport Harbor
Wind exposure off the harbor is significant. We fasten panels to a 140 mph uplift rating and secure every ridge cap and gable trim to manufacturer specs.
Steppingstone
A mix of older bungalows and renovated homes. Deck condition varies widely, so we inspect every board during tear-off and replace anything soft or cracked before underlayment goes down.
Salt air off the bay accelerates corrosion and finish wear
Shingle granules break down faster here than inland, and bare metal fasteners can corrode. We use galvalume or galvanized panels with factory paint and neoprene-washered screws rated for coastal exposure.
Nor'easters push sustained wind gusts off the water
Improperly fastened panels can lift or tear loose in a storm. We follow manufacturer screw patterns exactly, which keeps the assembly rated to 140 mph and your warranty valid.
Freeze-thaw cycles from December through March
Ice dams form along eaves and push water under shingles. We run ice and water shield along every eave and valley, and the corrugated profile sheds snow and water fast.
Summer heat and humidity drive cooling costs up
Dark roofs absorb heat and radiate it into the attic. Light-colored metal panels reflect solar heat, which typically cuts summer cooling costs 10 to 25 percent.
Before and after
What a successful service visit changes.
Freeport Ranch: Shingles to Corrugated Metal
Before
A 1,400-square-foot ranch near the Nautical Mile had 17-year-old asphalt shingles with granule loss, three active leaks, and soft decking around two pipe boots. The homeowner was patching the roof every spring and had already replaced it once in 15 years.
After
We tore off the old shingles, replaced 120 square feet of rotted decking, and installed 26-gauge corrugated metal panels with synthetic underlayment and ice and water shield. The job took four days. The roof now carries a 140 mph wind uplift rating and a 40-year finish warranty.
Maintenance: Rinse the panels once a year to remove salt residue, check fasteners each spring, and keep gutters clear. That is it. No annual patching, no granule loss, no repair calls after every storm.
Baldwin Colonial: Storm-Damaged Roof Rebuilt
Before
A nor'easter tore shingles off a 2,200-square-foot colonial in Baldwin and opened a leak over the master bedroom. The insurance adjuster documented the damage, and the homeowner decided to upgrade to metal rather than re-shingle a roof that had already failed twice.
After
We installed corrugated metal panels in a light gray finish over new underlayment and ice and water shield. The full tear-off and installation took five days. The homeowner's summer cooling bill dropped about $40 a month, and the roof has stayed dry through two subsequent storms.
Maintenance: Annual gutter cleaning and a spring fastener check keep the roof performing. We recommend a professional inspection every three years to catch any backed-out screws or sealant wear before they become leaks.
Merrick Garage: Low-Slope Metal Retrofit
Before
A detached two-car garage in Merrick had a low-slope shingle roof that ponded water after every rain. The shingles were curling, the deck was soft in two spots, and the homeowner was tired of replacing the roof every 10 years.
After
We replaced 60 square feet of decking and installed corrugated metal panels with sealed seams and ice and water shield along the low edge. The job took two days. Water now sheds off the roof within minutes of a storm, and the ponding problem is gone.
Maintenance: Keep the gutter clear at the low edge so water has somewhere to go. Check the panel fasteners once a year and reseal any penetration that shows wear. The roof should last 40-plus years with that routine.
Problems we solve
Problems Our Corrugated Metal Roofing Solves
Most of the calls we get in Freeport come down to the same handful of problems. Metal panels solve them at the source instead of patching the symptom every year.
Shingles failing every 12 to 15 years from salt air
Salt air off the bay eats shingle granules faster than inland. You end up paying for tear-off and replacement every decade and a half, plus repair calls in between. We install corrugated metal panels with a factory paint finish that holds 30 to 40 years in coastal conditions. The galvalume substrate resists salt-air corrosion, so you stop the replace-every-15-years cycle and get a roof that lasts 40 to 70 years.
Roof leaks after every heavy storm
Missing shingles, failed flashing, and backed-out fasteners let water into your ceilings and insulation. Left alone, that leads to rotting decking and mold inside the house. We tear off the failing roof, repair the deck, and install corrugated metal panels with proper underlayment and ice and water shield. Fasteners go in on a chalk line with neoprene washers, and every penetration gets sealed. Your roof stops leaking because the failure points are gone.
Ice dams forming along eaves in winter
Freeze-thaw cycles push water under shingle edges, which causes interior leaks and rots the fascia. Ice dams are one of the most common winter repair calls we get in Nassau County. The corrugated profile sheds snow and water fast, and we run ice and water shield along every eave and valley. That combination stops the water from backing up under the roof. Fewer ice dams means fewer winter leaks and less fascia rot.
High summer cooling bills from heat absorbed by the roof
Dark asphalt shingles soak up solar heat and radiate it into your attic. That drives up cooling costs 10 to 25 percent in July and August and shortens the life of your AC system. Light-colored corrugated metal panels reflect solar heat instead of absorbing it. Homeowners typically see summer cooling costs drop $30 to $60 a month after installation. The roof stays cooler, the attic stays cooler, and your AC works less.
Proof behind the promise
Licensed, Certified, and Warrantied
Technical expertise
Two Decades of Metal Roofing Experience
Roof Repaire Freeport has been installing and repairing roofs since 2005, which means 21 years of South Shore storms, salt air, and freeze-thaw cycles behind every panel we set. Our crews hold OSHA 10 and OSHA 30 cards, and we install to manufacturer specs so your warranty stays valid. We have worked on everything from 1920s bungalows near the Nautical Mile to new-build colonials in the Meadowbrook section. That range matters when your roof has an odd pitch, an added dormer, or three layers of old shingles hiding deck damage.
- 21 years serving Freeport and Nassau County, founded in 2005.
- OSHA 10 and OSHA 30 certified installers on every metal roof crew.
- GAF Master Elite and Owens Corning Preferred Contractor credentials.
- NRCA member with manufacturer certifications for metal and shingle systems.
- Thousands of square feet of corrugated panel installed on South Shore homes.
Customer stories
What Freeport Homeowners Say About Our Metal Roofs
Dana R.Homeowner, Freeport
We were replacing shingles every 12 years because of the salt air off the bay. Roof Repaire Freeport installed corrugated metal panels in four days and the house has been dry through two nor'easters since. The crew was clean, the price matched the estimate, and they walked me through the whole job. Should have done this a decade ago.
Marcus T.Homeowner, Baldwin
Our old roof leaked every time it rained hard. They found the flashing failure, repaired the deck, and installed a new corrugated metal roof. My summer electric bill dropped about $40 a month. They showed up when they said they would and finished when they said they would.
Priya S.Homeowner, Merrick
I called three roofers and Roof Repaire Freeport was the only one who got on the roof the same day. They explained the difference between 26- and 29-gauge panels, showed me samples, and gave a written price. The metal roof looks great and the yard was spotless when they left. Highly recommend.
How much does corrugated metal roofing cost in Freeport NY?
Most corrugated metal roof installations in Freeport run $9 to $16 per square foot installed, or roughly $14,000 to $28,000 for a typical 1,500- to 1,800-square-foot home. That covers tear-off, underlayment, ice and water shield, panels, trim, and cleanup. Steeper pitches, multiple dormers, and deck repairs push the number up. We give you a fixed written price before any work starts.
How long does a corrugated metal roof last in Freeport?
A properly installed corrugated metal roof lasts 40 to 70 years in Freeport's coastal climate. The galvalume or galvanized steel substrate resists salt-air corrosion, and the factory paint finish holds 30 to 40 years before it needs a recoat. Compare that to 12 to 15 years for asphalt shingles in the same salt air, and the math favors metal over the life of the home.
Who installs corrugated metal roofs in Freeport New York?
Roof Repaire Freeport installs corrugated metal roofs across Freeport, Nassau County, and the South Shore villages. We have been in business since 2005, hold OSHA 10 and OSHA 30 certifications, and carry GAF Master Elite and Owens Corning Preferred Contractor credentials. Call us for a same-day estimate and we will walk your roof, measure it, and price the job in writing.
Are corrugated metal roofs good for Freeport NY weather?
Yes. Corrugated metal roofs handle Freeport's nor'easters, salt air, hail, and freeze-thaw cycles better than asphalt. The panels carry wind uplift ratings up to 140 mph when fastened correctly, shed rain fast to prevent ponding, and resist the ice dams that form along eaves after a winter freeze. They also reflect summer heat, which cuts cooling costs 10 to 25 percent.
Frequently asked questions
Frequently Asked Questions About Corrugated Metal Roofing
Not seeing your question? Our local team can help you understand urgency, scheduling and what to expect.
Ask the local teamRelated services
Related Roofing Services
Roof Installation
New corrugated metal roof installation Freeport NY starts with a full tear-off and deck inspection. We install underlayment, ice and water shield, panels, and trim to manufacturer specs so your warranty holds. Most homes are done in three to five days.
View service
Roof Replacement
When your old shingle roof is beyond patching, we replace it with corrugated metal panels built for coastal weather. We handle tear-off, disposal, deck repair, and full installation. You get a 40- to 70-year roof and a written workmanship warranty.
View service
Roof Repair
Loose fasteners, backed-out screws, and failed pipe boots are common on older metal roofs. We reseal penetrations, replace damaged panels, and re-torque fasteners with neoprene washers. Most corrugated metal roof repair Freeport New York calls are done in a single visit.
View service
Roof Inspection
A full roof inspection catches flashing failure, rusted fasteners, and early panel corrosion before they become leaks. We check the deck from the attic side, photograph problem areas, and give you a written report. Ideal before buying a home or after a major storm.
View serviceContact the local team
Contact our Freeport roofing team
Call 342425679 or email us and we will get back to you the same business day. For active leaks and storm damage, we answer around the clock. We serve Freeport and the surrounding Nassau County communities, and we can usually schedule an inspection within a few days.